No scrape. No scuff. No noise.Free US shipping until Dec 31

Chair Feet

Chair feet are the caps, covers, glides and plugs on the end of each chair leg, and this collection holds replacement chair feet for ones that have worn through, split or gone missing. Some people call them chair bottoms: the parts at the bottom of each leg that touch the floor. There are five products here (two kinds of slip-on cap, a stretch cover, a nail-on glide and a push-in plug), and every pack holds one size.

Start with the leg, because feet for chair legs are sized to the leg end, not to the chair.

On a metal tube leg, a cap slips over the outside: see tube leg caps in round and square sizes. On a solid wooden leg with a flat end, felt chair glides tap in with one center nail. For round legs between sizes, felt bottom chair leg covers stretch to fit a range, such as 22 to 32 mm.

If the old foot sat inside the tube, it was a plug, and a new plug of the same tube size replaces it. Measure before you order: our page on how to measure chair legs for protectors shows where to put the ruler.

How to choose replacement chair feet

Match the foot to the leg first (material, shape and size), then to the floor.

Type Fits Floor Attaches by
Tube leg caps Round 16 or 30 mm; square 20, 25 or 30 mm; metal or wooden legs Hard floors. Clear silicone, grips. Slips over the leg end
Felt lined metal chair leg caps Round 16, 19, 22 or 25 mm; square 20 mm metal tube Hard floors. Felt pad, slides. Slips over the leg end
Felt bottom chair leg covers, 16 pack Round legs 16 to 22, 22 to 32 or 30 to 40 mm wide Hard floors. Felt base, slides. Stretches over the leg end
Felt chair glides, nail-on, 100 pack Solid wooden legs with a flat end 20 mm or wider Hardwood, laminate, vinyl, tile. Slides. One nail tapped into the wood
Chair leg plugs, 10 pack Open round tube: 16, 19, 22, 25, 28, 30, 32 or 38 mm outside Tile, concrete. Hard plastic, slides. Pushes into the tube

Over the leg, into the tube, or into the wood?

A cap or cover goes over the outside, so it works on hollow tube and on solid legs. A plug goes inside, so the tube must be round, hollow and open at the end. A nail-on glide needs solid wood to hold the nail.

For round wooden legs where you want the finish to show, clear chair leg caps slip over the leg end and have a felt pad on the base. For a flat wooden leg end you would rather not nail, self adhesive chair glides stick on; they are 22 mm (0.87 in) across, so the leg base should be that wide or wider.

Slide or grip?

Felt slides, which suits dining and desk chairs that are pulled in and out. The clear silicone tube leg caps grip, so stools and chairs stay put but take more effort to move. On hardwood, felt is the gentler choice.

How to measure for chair feet

  1. Pull off the old foot and wipe the leg end clean.
  2. Measure straight across the outside of the leg end in millimeters. On a round leg, measure through the center. On a square leg, measure both sides to check it is square and not rectangular.
  3. If the old foot was a plug, measure the outside of the tube, not the old plug, and check that the end is open.
  4. For nail-on glides, check that the wooden leg end is flat and at least 20 mm (about 3/4 in) across.
  5. In inches: 5/8 in is about 16 mm, 3/4 in 19 mm, 7/8 in 22 mm and 1 in 25 mm.

The caps are sized to the leg and stretch very little, so pick the size that matches your number. The felt bottom covers stretch, so each size fits a range.

Honest limits

  • Each pack holds one size, and each pack of covers one color. Chairs with two leg sizes need two packs.
  • The plugs in this grid fit round tube only. For 1.5 in (38 mm) open square tube, see square chair leg plugs. For smaller square tube, use a square cap: tube leg caps in 20, 25 or 30 mm, or felt lined caps in 20 mm.
  • For square wooden legs, square silicone chair leg caps fit legs 19 to 28 mm or 35 to 40 mm wide.
  • Nail-on glides come in 20 mm only and need solid wood. They will not fix to metal or plastic legs.
  • None of the feet in this grid screw in. A leg with a threaded hole or an old threaded stem needs a threaded glide in the same thread, such as M6 or M8, so measure the old stem across the threads first.
  • Grit under any foot can scratch a soft floor. Replace felt when it wears thin.

For more caps that go over steel tube, see metal chair leg caps, and for steel folding chairs, folding chair feet caps. To see every protector for chair legs, go to chair leg floor protectors.

Related guides: How to Fix a Wobbly Chair and What Are Chair Glides?

Chair Feet: questions and answers

How do I replace chair feet?

Pull off the old foot, wipe the leg end clean and measure across it in millimeters. Then fit a cap, cover, glide or plug of the same size. Caps, covers and plugs push on or in by hand; nail-on glides need a hammer. Our <a href="/pages/size-guide">size guide</a> shows how to measure.

Are chair bottoms the same as chair feet?

Yes, when you mean the part at the bottom of each leg that touches the floor. Replace chair bottoms the same way: measure the leg end in millimeters and fit a cap, cover, glide or plug of that size. These parts fit leg ends only; they do not replace a chair seat.

What if the old foot was inside the tube?

Then it was a plug. Measure the outside diameter of the tube, check that the end is open, and choose <a href="/products/chair-leg-plugs-tube-inserts">chair leg plugs</a> in that size: 16, 19, 22, 25, 28, 30, 32 or 38 mm. They fit round tube only.

Wooden or metal legs?

Wooden legs take nail-on felt glides, or slip-on caps and covers. Metal tube takes caps, covers or plugs. The glides need solid wood for the nail to hold, so they will not fix to metal.

Do replacement chair feet slide?

Felt faces slide: the nail-on felt glides, the felt lined caps and the felt bottom covers. The clear silicone tube leg caps grip, so the chair stays put but takes more effort to pull out. The hard plastic plugs slide on tile and concrete.

How many chair feet come in a pack?

Each pack holds one size, and the count differs by product: the felt bottom covers come 16 to a pack, the plugs 10 and the nail-on glides 100. Each product page shows its pack count. A four-legged chair needs four feet, so a 16 pack of covers fits four chairs.

Do they fit square legs?

Some do. <a href="/products/tube-leg-caps-round-square">Tube leg caps</a> come in square 20, 25 and 30 mm, and felt lined metal chair leg caps in square 20 mm. The plugs and felt bottom covers here are made for round legs. For 1.5 in square tube, see <a href="/products/square-chair-leg-plugs-1-5-inch">square chair leg plugs</a>.

Cart • 1 item

Loading your bag…