Felt Chair Glides, Nail-On
100 nail-on felt glides, 20 mm, one pack
$16.99 · Free US shipping until Dec 31
Felt chair glides with a center nail that you tap into the bottom of wooden legs, so the chair slides on felt instead of scraping the floor. One pack of 100 covers 25 four-legged chairs.
- 100 glides, 20 mm (0.79 in) across
- Gray felt face on a brown plastic disc
- One metal center nail: tap it into a wooden leg
- For wooden legs on hardwood, laminate, vinyl and tile
Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.
- Secure checkout: pay with PayPal, Shop Pay or card
- Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
- 30-day refund policy · Size guide
Felt chair glides with a nail in the center are the simple fix for wooden chairs that scrape the floor. Each glide is a 20 mm brown plastic disc with a gray felt face and one metal nail. Tap the nail into the bottom of a wooden leg and the chair slides on felt instead of bare wood. This pack holds 100 glides, enough for 25 four-legged chairs.
Comparing options? See all chair glides and chair sliders, browse furniture pads for hardwood floors, or read how to measure chair legs for protectors before you order.
What is in the pack
| Detail | What you get |
|---|---|
| Glides | 100 |
| Diameter | 20 mm (0.79 in, about 3/4 in) |
| Felt face | Gray felt, set into the disc |
| Disc | Brown plastic |
| Fixing | One metal nail in the center |
| Covers | 25 chairs with 4 legs |
How to choose and measure
Turn the chair over and measure across the bottom of one leg. These glides suit wooden legs whose flat end is 20 mm (0.79 in) or a little wider, so the whole disc sits under the wood and nothing overhangs. On a much wider leg the glide still works, it just covers less of the leg end.
The leg must be solid wood at the bottom, because the nail needs wood to grip. Check that the end is flat and not cut at an angle.
How to fit them
- Turn the chair upside down on a soft cloth.
- Pull out any old glide or nail and wipe the leg end clean.
- Stand a glide on the center of the leg end, nail against the wood, felt facing up.
- Tap the center of the felt with a hammer until the brown disc sits flat on the wood.
- Repeat on every leg so the chair stays level.
On hard woods such as oak, or on a thin leg, drill a small pilot hole first so the wood does not split.
Where nail-on chair glides work, and their limits
Felt slides on hard floors: hardwood, laminate, vinyl and tile. A nailed glide cannot peel off the way a stick-on pad can, which suits dining and kitchen chairs that are pulled in and out every day. Felt does pick up grit and wear thin over time, and that is when felt pads scratch hardwood floors. When the felt wears, pry the old glide off with a flat screwdriver and nail in a new one. A set of 6 dining chairs uses 24 of the 100 glides, so the rest are spares.
They are not the right fit for every leg:
- Metal or plastic legs: the nail has nothing to hold. Use metal chair leg caps instead.
- Legs with a threaded hole in the end: they need a glide with a threaded stem that screws into the hole, not a nail.
- Splayed legs that meet the floor at an angle: a flat glide would sit on its edge, so choose angled chair leg floor protectors.
- Legs narrower than 20 mm at the bottom: a slip-on cap fits better. See chair leg caps.
Questions
What size are they?
20 mm (0.79 in, about 3/4 in) across. They suit wooden legs whose flat end is 20 mm or a little wider, so the glide sits fully under the leg. The size guide shows how to measure.
How do I fit them?
Turn the chair over, stand the glide on the center of the leg end with the nail against the wood, and tap the felt with a hammer until the disc sits flat. On hard wood, drill a small pilot hole first.
Can they go on metal legs?
No. The nail needs solid wood to hold. For metal tube legs, see metal chair leg caps.
How many chairs does a pack cover?
100 glides cover 25 four-legged chairs. With fewer chairs, keep the rest as spares for when the felt wears.
Will they fall off?
A nailed glide cannot peel off like a stick-on pad. To replace one, pry it off with a flat screwdriver; it leaves a small nail hole in the leg end. Our guide on how to replace chair glides shows how to reuse or fill that hole.
What color are they?
The plastic disc is brown, which blends with darker wood legs. The felt that touches the floor is gray.










