No scrape. No scuff. No noise.Free US shipping until Dec 31
Square chair leg plugs: one pushed flush into the end of a square steel tube, one loose showing its two ribs and hollow underside
All 24 black square plugs laid out head up in four rows of six
Black square plug fitted flush in the foot of a brushed steel chair leg on a grey tile floor
Hand holding a square plug, ribs first, at the open end of a square steel tube
One square plug standing on edge showing its flat head and two ribs, beside one turned over to show the hollow underside

Square Chair Leg Plugs for 1.5 Inch Tube

24 black plugs for 1.5 in (38 mm) square tube

$15.99 · Free US shipping until Dec 31

Ribbed black plastic plugs that push into the open ends of 1.5 inch square metal tube legs. The flat head covers the sharp cut edge so bare steel no longer scrapes the floor.

  • 24 black PE plastic plugs in one pack
  • Fits 38 x 38 mm (1.5 in) square tube, outside size
  • For tube walls 0.5 to 1.5 mm thick
  • Ribbed body: push in by hand or tap with a mallet
SizeHow to measure

Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.

  • Secure checkout: pay with PayPal, Shop Pay or card
  • Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
  • 30-day refund policy · Size guide
American Express Apple Pay Diners ClubDiscoverGoogle Pay Mastercard PayPalShop Pay Visa

Square chair leg plugs close the open ends of 1.5 inch (38 mm) square metal tube on chairs, tables, benches and shelving. Each plug has a flat square head and a ribbed body. Push the ribs into the tube and the head sits over the cut edge, so bare steel no longer scrapes the floor and dust stays out of the tube. One pack holds 24 plugs, enough for six four-legged chairs or tables.

Not sure this is the right part? Browse all plastic chair glides for metal legs and metal chair leg caps, or read how to measure chair legs for protectors first.

Size and what is in the pack

Part Metric Inches
Fits square tube (outside) 38 x 38 mm 1.5 x 1.5 in
Tube wall thickness 0.5 to 1.5 mm 0.02 to 0.06 in
Head 38.8 x 38.8 mm 1.53 x 1.53 in
Head thickness 3.7 mm 0.15 in
Widest rib 37.6 mm 1.48 in
Inner end (narrowest) 31.3 mm 1.23 in
Total height 17.7 mm 0.70 in
Weight 6.94 g each 0.24 oz each
Plugs per pack 24

Sizes come from the maker and are measured by hand, so allow a few tenths of a millimeter either way. The plugs are black polyethylene (PE) plastic. We stock them in black and in this one size only.

How to measure your tube

Turn the chair or table over and look at the bottom of a leg. These plugs only fit if the end is open and square.

  1. Measure across one flat outside face of the tube. Calipers give the cleanest reading. It should read 38 mm, which is 1.5 in.
  2. Measure the other face too. A tube that is 38 mm one way and narrower the other way is rectangular, and these will not fit it.
  3. Look at the wall. It should be 0.5 to 1.5 mm thick (0.02 to 0.06 in).

How to fit them

  1. Wipe the inside of the tube end so grit does not sit under the head.
  2. Line the plug up square with the opening, ribs first.
  3. Press it in by hand until the head sits flat on the tube edge.
  4. If it is stiff, tap the head with a rubber mallet. If it still will not go, the maker suggests trimming a little off the rib edges with a craft knife and trying again.

No glue or screws are needed. The ribs flex as they go in and press against the inside walls of the tube to hold the plug in place.

Where they work and honest limits

Square plugs suit metal dining chairs, bar stools, desk and table frames, benches and shelving built from 1.5 inch square tube. As 1.5 inch square tube end caps, they replace a plug that has cracked or gone missing, and they give a new frame a finished end. If the old plug is stuck or its head has snapped off, our guide to replacing chair glides shows how to pull it out.

The head is hard plastic, not felt or rubber. It stops the raw metal edge from gouging a floor, and it slides on tile, vinyl and concrete. On soft hardwood, any hard surface can still leave marks if grit gets trapped under it, so keep the floor swept. For a softer contact face, see square chair leg caps with felt bases, which fit over the outside of the leg instead.

They do not fit round tube. For round legs, see chair leg plugs in sizes from 16 to 38 mm. They also do not fit square tube smaller or larger than 38 mm; for 20, 25 or 30 mm square legs, see the slip-over caps among our chair tips.

Questions

What size tube do they fit?

Square tube that measures 38 x 38 mm (1.5 in) on the outside, with a wall 0.5 to 1.5 mm thick. Measure across one flat face; the size guide shows how.

Do you have other square sizes?

Not yet. We stock this plug in the 1.5 inch (38 mm) size only. For round tube, see chair leg plugs.

How do I fit them?

Push them in by hand, or tap the head with a rubber mallet. If a tube is tight, trim a little off the rib edges with a craft knife and try again.

How many come in a pack?

24 plugs, enough for six four-legged chairs or tables.

Will they protect a hardwood floor?

They cover the sharp metal edge, so the tube no longer gouges the floor. The face is hard plastic, so keep grit swept away. For a softer face, see square chair leg caps.

More in Plastic Chair Glides for Metal Legs

See all Plastic Chair Glides for Metal Legs

Cart • 0 items

Loading your bag…