No scrape. No scuff. No noise.Free US shipping until Dec 31
Knitted chair socks in gray, one on a wooden chair leg and one on its side showing the round felt bottom
All 24 gray knitted chair socks laid out in four rows of six, felt bottoms showing
Gray knitted socks on all four legs of a wooden dining chair on a hardwood floor
Hand pulling a gray knitted sock up over the end of a wooden chair leg
Brown knitted chair sock on a wooden chair leg beside one showing its tan felt bottom
Brown knitted socks on the legs of a dark wood chair on a light hardwood floor

Knitted Chair Socks

24 knitted socks with felt bottoms, one pack

$17.99 · Free US shipping until Dec 31

Ribbed stretch knit socks that pull over the feet of chair and table legs, each closed at the bottom with a round felt pad. One pack of 24 covers six four-legged chairs, in gray or brown.

  • 24 knitted socks, enough for six chairs
  • Closed bottom with a round felt pad
  • About 40 mm (1.6 in) across, 70 mm (2.8 in) long
  • Pulls on by hand: no glue, nails or tools
Color

Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.

  • Secure checkout: pay with PayPal, Shop Pay or card
  • Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
  • 30-day refund policy · Size guide
American Express Apple Pay Diners ClubDiscoverGoogle Pay Mastercard PayPalShop Pay Visa

Knitted chair socks pull over the feet of chair and table legs so a soft layer sits between the wood and your floor. Each sock is a short tube of ribbed stretch knit, closed at the bottom with a round felt pad. A pack holds 24 socks, enough for six four-legged chairs, in gray or brown.

Shopping for something else? Our cat paw chair leg socks add a paw print design, and the full range of chair leg floor protectors covers caps, pads and glides. Not sure of your leg size? Read how to measure chair legs for protectors, or browse all our chair leg socks.

What is in the pack

Detail Value
Socks per pack 24 (six chairs)
Width across the base About 40 mm (1.6 in)
Length About 70 mm (2.8 in)
Bottom Round felt pad
Knit Ribbed stretch knit
Colors Gray with gray felt, or brown with tan felt

Sizes are the supplier figures, measured on the brown sock. The gray sock is sold at the same weight and is pictured without measurements, so it may differ slightly. Knit can vary by a few millimeters.

How to choose

Measure across the bottom of one leg. For a round leg, measure straight across. For a square leg, measure from corner to corner, because the felt base is round.

These socks suit legs whose foot is about 40 mm (1.6 in) across or a little narrower. The knit stretches to grip the leg, but the felt base does not stretch.

On a much wider leg the edge of the leg sits outside the felt. On a much thinner leg the base is wider than the leg end and the sock can sit loose.

Pick the color that blends in: gray for white, gray or light wood furniture, brown for walnut, oak and other darker woods.

How to fit them

  1. Tip the chair back or lay it on its side on a soft surface.
  2. Stretch the open top of a sock with your fingers.
  3. Pull it over the end of the leg until the felt pad sits flat under the foot.
  4. Smooth the knit up the leg so it sits straight. No glue, nails or tools are needed.

To take them off, roll the top down and slide the sock off. Nothing is left on the leg.

Where knitted socks work, and their limits

Knitted socks suit wooden chairs, stools and small tables on hardwood, laminate, vinyl and tile. The felt slides across a hard floor more quietly than a bare wooden foot, and the knit covers the bottom of the leg, so it knocks more softly against baseboards and other chairs.

They hold on by stretch alone. On dining chairs that are dragged in and out many times a day, a sock can twist or work loose, and you may need to pull it straight now and then. For those chairs, fitted chair leg caps or felt bottom chair leg covers hold the leg more closely, and on slim round legs, tennis ball caps for chair legs push on with no glue.

Fabric soaks up spills and collects dust and hair, so keep them away from wet floors and shake them out from time to time. They are not made for chair wheels, hairpin legs or sled bases.

Questions

What are they made of?

A ribbed stretch knit (the supplier lists spandex) with a round felt pad across the closed bottom.

Do they have a felt base?

Yes. Each sock is closed at the bottom with a round felt pad, so felt, not only knit, sits on the floor.

How many come in a pack?

24 socks, enough for six four-legged chairs.

Do they fit square legs?

The knit stretches over square legs too. The felt base is round and about 40 mm (1.6 in) across, so measure the leg corner to corner; if that is much more than 40 mm, the corners sit outside the felt. The size guide shows how to measure.

Will they stay on chairs that are dragged every day?

They hold by stretch alone, so on chairs pulled in and out all day a sock can twist and need straightening. Chair leg caps fit the leg more closely.

Can I use them on chairs with wheels?

No. They are made for plain leg ends on hard floors, not casters, hairpin legs or sled bases.

More in Chair Leg Socks

See all Chair Leg Socks

Cart • 0 items

Loading your bag…