No scrape. No scuff. No noise.Free US shipping until Dec 31

Plastic Chair Leg Caps

Plastic chair leg caps cover the bottom of a chair, stool or table leg so bare wood or metal stops scratching the floor. Everything here is plastic, in two forms: clear PVC caps with a black felt pad underneath that slip over the leg, and black plastic plugs that push into the open end of a metal tube.

For thin steel tube legs, choose the felt lined metal chair leg caps in round 16, 19, 22 or 25 mm or square 20 mm. For thick table and sofa legs, the large furniture leg caps come in round 38, 50 or 60 mm and square 38, 40, 50 or 60 mm. If the leg ends in an open round tube, chair leg plugs sit inside it and cover the cut edge.

Each size is exact, so measure before you order. Our guide on how to measure chair legs for protectors shows where and how.

How to choose plastic chair leg caps

Start with the leg end, then match the size. Each pack holds one shape and one size.

Product Fits Goes on
Felt lined metal chair leg caps: clear PVC, felt base, 4 per pack (one chair) Round 16, 19, 22 or 25 mm; square 20 mm Slips over the leg; felt slides
Large furniture leg caps: clear PVC, felt base, 4 per pack (one table or sofa) Round 38, 50 or 60 mm; square 38, 40, 50 or 60 mm Slips over the leg; felt slides
Chair leg plugs: black ribbed plastic, 10 per pack Open round tube, 16, 19, 22, 25, 28, 30, 32 or 38 mm outside Pushes into the tube; plastic head slides
Square chair leg plugs: black PE plastic, 24 per pack Open 38 x 38 mm (1.5 in) square tube, 0.5 to 1.5 mm wall Pushes into the tube; plastic head slides

Cap or plug? A cap goes over the outside of the leg and works on wood or metal. A plug goes inside a hollow metal tube, so it only fits an end that is open and not squashed; if the end is closed or bent, choose a cap. Either way, they work as plastic feet for chairs, stools and tables.

Felt or plain plastic? Both are plastic floor protectors for chair legs. The clear caps put felt on the floor, which slides on hardwood, laminate, tile and vinyl and is the gentler choice on hardwood. The black plugs have no felt: their plastic head covers the sharp cut edge of the tube and slides, so keep grit swept away.

How to measure for a cap or plug

  • Tip the chair over and measure the very bottom of the leg, where the cap or plug will sit.
  • Round leg: measure straight across the center. 5/8 in is 16 mm, 3/4 in is 19 mm, 7/8 in is 22 mm and 1 in is about 25 mm.
  • Square leg: measure one flat side, edge to edge, not corner to corner.
  • For a cap, the size is the inside of the cap, so it should equal the outside of your leg.
  • For a plug, the size is the outside of the tube. Also check the end is open and hollow with a thin wall.
  • Calipers give the most exact number. A ruler works if you read it in mm.

What these caps will not do

  • They come in exact sizes only. The PVC caps are soft enough to squeeze but stretch very little: a leg bigger than the cap will not go in, and one more than about 1 mm smaller sits loose and can slip off.
  • Caps come in these sizes only: round 16, 19, 22, 25, 38, 50 and 60 mm; square 20, 38, 40, 50 and 60 mm. So there is no cap here for a 32 mm or 45 mm round leg, or for a 1 in (25 mm) square leg. An open round tube of 28, 30 or 32 mm can take a plug instead.
  • Caps fit straight, upright leg ends. They do not suit sled base runners that rest along the floor, splayed legs or tapered ends.
  • The square plugs come in the 1.5 in (38 mm) size only.
  • Everything here slides. To keep a chair in place, see silicone chair leg protectors.
  • Felt wears with use and does little on carpet. Check the pads now and then and replace caps when the felt is thin.

For every cap by leg shape, see all chair leg caps. For steel tube legs, see metal chair leg caps and plastic chair glides for metal legs.

Related guide: how to stop chairs from scratching floors

Plastic Chair Leg Caps: questions and answers

Plastic or silicone chair leg caps?

These plastic caps for chair legs are clear PVC made to one exact size, with a felt pad that slides. Silicone caps grip the floor instead, so the chair stays put. See <a href="/collections/silicone-chair-leg-protectors">silicone chair leg protectors</a>.

Do plastic chair leg protectors scratch the floor?

The clear caps do not: they put a felt pad on the floor, the gentlest face here. The black plugs have no felt; their hard plastic head covers the sharp tube edge and slides, but grit trapped under it can scuff a soft floor, so keep the floor swept.

How exact must the size be?

Exact. A cap size is the inside of the cap, so it must equal the outside of your leg; the PVC squeezes but stretches very little. A plug size is the outside diameter of the tube. Measure in mm with our <a href="/pages/size-guide">size guide</a>.

Are they see-through?

The clear PVC caps are, so the leg finish shows. The plugs are black.

Cap or plug?

A cap slips over the outside of the leg. A plug pushes into an open metal tube end, and its head covers the cut edge. If the tube end is closed, bent or squashed, choose a cap.

How many come in a pack?

Felt lined metal chair leg caps: 4, enough for one chair. Large furniture leg caps: 4, enough for one four-legged table or sofa. Round chair leg plugs: 10, enough for two chairs with two spares. Square chair leg plugs: 24, enough for six chairs or tables. Every pack is one size.

Cart • 1 item

Loading your bag…