No scrape. No scuff. No noise.Free US shipping until Dec 31
Angled chair leg floor protectors on a splayed wooden stool leg, close-up of the brown cap and its flat felt sole
Eight round brown angled caps with felt soles, the full pack, standing in two rows of four
Round brown angled caps on the splayed wooden legs of a stool on an oak floor
Hand pushing a round brown angled cap onto a leg of an upturned wooden stool, the tilted felt sole facing up
Eight square brown angled caps with felt soles, the full pack, standing in two rows of four
Square brown angled cap on a splayed square walnut table leg, the cup leaning with the leg and the felt sole flat on a tile floor

Angled Chair Leg Floor Protectors

8 brown caps with felt soles, one pack

$18.99 · Free US shipping until Dec 31

Slip-on caps with a felt sole tilted 15 degrees, so it sits flat under legs that splay outward. Choose round or square, in two sizes for legs 20 to 35 mm across.

  • 8 caps per pack, brown TPE rubber with a felt sole
  • Sole set at 15 degrees for splayed legs
  • Round or square, 1 in (20-28 mm) or 1.25 in (27-35 mm)
  • Slips on: no nails, screws or glue
Leg shape
SizeHow to measure

Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.

  • Secure checkout: pay with PayPal, Shop Pay or card
  • Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
  • 30-day refund policy · Size guide
American Express Apple Pay Diners ClubDiscoverGoogle Pay Mastercard PayPalShop Pay Visa

Angled chair leg floor protectors are slip-on caps with a felt sole set at 15 degrees, so they sit flat under legs that splay outward. A flat cap on a leaning leg touches the floor only along one edge, which wears through quickly and can scratch.

These caps tilt the felt back to level, so the whole sole meets the floor. Each pack holds 8 brown caps, enough for two four-legged stools or chairs.

Shopping for a different leg? See all bar stool leg caps, chair glides and chair leg caps, or read how to measure chair legs for protectors.

Sizes and what is in the pack

Size Fits legs measuring In the pack
1 in, round or square 20 to 28 mm (0.79 to 1.10 in) 8 caps
1.25 in, round or square 27 to 35 mm (1.06 to 1.38 in) 8 caps
Material TPE rubber cup, felt sole
Color Brown
Sole angle 15 degrees
Wall thickness About 3.5 mm
Fitting Slips on, no nails or glue

How to choose the right size

Measure across the bottom of the leg, about 1 cm up from the floor. On a round leg, measure the diameter. On a square leg, measure from one flat side to the opposite side.

Pick the size whose range covers your number. Legs under 20 mm or over 35 mm across are outside both sizes, so these caps will not fit them. If your leg measures 27 or 28 mm, both sizes fit: the 1 in cap grips tighter, the 1.25 in cap goes on more easily.

To check the angle, hold a phone with a level app flat against the leg. A reading of about 15 degrees from vertical (75 degrees from the floor) is what these caps are shaped for.

How to fit them

  1. Turn the chair or stool upside down on a soft surface.
  2. Push a cap over the end of each leg. The rubber stretches, so work it on with a slight twist.
  3. Stand the furniture up and look at each foot from the side.
  4. Turn any cap that rests on its edge until the whole felt sole touches the floor. Round caps turn freely; square caps turn in quarter steps.

Where they work, and their limits

Use them as slanted chair leg caps on splayed stools, counter stools, dining chairs and table legs, round or square, in wood or metal. The felt sole also works as chair glides for angled legs, sliding on hardwood, laminate, vinyl and tile. The cup has a closed bottom, so the end of the leg stays covered.

They are made for one angle. The further your legs are from 15 degrees, the more the felt rides on one edge. Legs that stand straight up need a flat cap instead: see chair leg caps. For square legs that are not splayed, see square chair leg caps. Felt is for hard floors and does little on carpet. Brown is the only color.

Questions

Why do angled legs need different caps?

A flat cap on a splayed leg touches the floor only at one edge, which wears fast and can scratch. A 15 degree sole sits flat, so the whole felt pad meets the floor.

What if my legs are not splayed 15 degrees?

They suit legs splayed by roughly that much; the further off, the more the felt rides on one edge. A leg close to vertical needs a flat cap: see chair leg caps.

Which size do I need?

Measure across the bottom of the leg. 1 in fits legs of 20 to 28 mm; 1.25 in fits 27 to 35 mm. The size guide shows how to measure.

Do they come in square?

Yes. Pick Square for square legs and measure from one flat side to the other. A square cap can only be turned a quarter turn at a time, so its tilt may not line up with a leg that splays toward a corner. Check each sole sits flat after fitting; round caps can be turned to any position.

Do they work on metal legs?

Yes, on round or square metal legs in the same size ranges. The rubber cup grips the leg by stretching over it.

How many come in a pack?

8 caps, enough for two four-legged chairs or stools.

More in Bar Stool Leg Caps

See all Bar Stool Leg Caps

Cart • 0 items

Loading your bag…