
Outdoor Chair Leg Caps
Outdoor chair leg caps cover the bare metal ends of aluminum and steel patio chair and table legs, so the tube no longer scrapes deck boards, patio stone or a porch floor. They are also sold as patio chair feet caps, patio chair leg caps or patio furniture leg protectors. Every cap here is sized to the outside of the leg in mm, so the first step is to measure one leg end and note its shape: round, square or rectangular.
Many patio chairs with flat-sided legs use rectangular tube; for those, see patio chair leg caps rectangular, 4 clear silicone caps per pack in 15 x 30, 20 x 30 or 25 x 38 mm. Round and square tube take tube leg caps, 4 per pack, enough for one patio table, so they also work as patio table leg caps.
For indoor metal chairs, browse all metal chair leg caps. Not sure of your size? Read how to measure chair legs for protectors before you order.
How to choose outdoor chair leg caps
Pick by the shape of the leg end first, then by whether the chair should grip or slide. The two silicone caps grip, which suits patio furniture on decks and stone. The felt lined caps slide, which suits a covered porch or a sunroom.
| Type | Fits tube (outside) | Floor | Attaches by |
|---|---|---|---|
| Rectangular silicone caps, 4 pack | Rectangle 15 x 30, 20 x 30 or 25 x 38 mm | Deck, patio stone, concrete; grips | Slips over the leg end |
| Tube leg caps, silicone, 4 pack | Round 16 or 30 mm; square 20, 25 or 30 mm | Deck, patio stone, hard floors; grips | Slips over the leg end |
| Felt lined caps, clear PVC, 4 pack | Round 16, 19, 22 or 25 mm; square 20 mm | Covered porch, sunroom, indoor hard floors; slides | Push-on snug fit, no glue |
Every pack holds 4 caps of one size, enough for one four-legged chair or table. For a set of four chairs, order four packs, and order a separate pack in the right size for any piece whose legs differ.
How to measure a patio chair leg
- Tip the chair onto a towel or cushion so the leg ends face you.
- Measure across the outside of the leg end in mm with a ruler or caliper.
- Round tube: measure the full width through the center. Square tube: measure one flat side, not the diagonal. Rectangular tube: measure the short side and the long side.
- Choose the cap that matches. For reference, 16 mm is about 5/8 in, 20 mm is about 3/4 in, 22 mm is about 7/8 in, 25 mm is about 1 in, 30 mm is about 1-3/16 in and 38 mm is about 1-1/2 in.
The silicone caps are firm and barely stretch. The felt lined caps flex a little, but each one is still made for one exact size. A leg bigger than the cap will not go in, and a leg more than about 1 mm smaller can sit loose and slip off. If your leg measures between two listed sizes, none of these caps will hold well.
What these caps cannot do
- The supplier states no sun or frost limits, so we do not promise a lifespan outdoors. Check the caps each spring and replace any that crack or wear through.
- The caps have closed bottoms, so rain running down a leg can sit inside. Lift them off now and then to let steel legs dry.
- Felt soaks up water and holds grit. Keep the felt lined caps under a roof, not on an open deck.
- All three caps here are clear, so the leg color shows through. None of them comes in a color.
- The caps here fit straight metal tube ends only. Solid bar legs, flattened or scrolled feet and sled bases need a different fitting.
- Square wooden legs 19 to 28 mm or 35 to 40 mm wide take square silicone chair leg caps. The supplier shows those only on wooden legs and states no outdoor use, so we make no outdoor promise for them.
Looking for pads and caps for indoor furniture too? See all furniture protectors.
Related guide: felt vs rubber chair leg caps, for when a chair should grip and when it should slide.
Outdoor Chair Leg Caps: questions and answers
Which patio chair feet caps suit my chairs?
Silicone caps sized to the tube: <a href="/products/patio-chair-leg-caps-rectangular">patio chair leg caps rectangular</a> for rectangular tube, and <a href="/products/tube-leg-caps-round-square">tube leg caps</a> for round and square tube. Both grip deck boards and stone instead of sliding. The supplier states no sun or frost limits, so check the caps each spring.
How do I measure a patio chair leg?
Measure the outside of the leg end in mm. Patio tube can be round, square or rectangular; for rectangles, measure both sides. This guide on <a href="/pages/size-guide">how to measure chair legs for protectors</a> shows each step.
Do you sell caps for wrought iron chairs?
Not yet. Until then, measure the leg end: if it is round tube of 16 or 30 mm, or square tube of 20, 25 or 30 mm, the <a href="/products/tube-leg-caps-round-square">tube leg caps</a> fit. Solid bar legs and flat or scrolled feet will not fit these caps.
Will these fit a sled base chair?
No. Leg caps fit over a vertical leg end. A sled base rests on a flat tube that runs along the floor, and a cap cannot fit over it.
Can I use them on a deck?
Yes. The silicone caps protect deck boards and patio stone from bare metal tube ends. Lift them off now and then, since rain can collect inside the closed bottom.
Can felt lined caps go outside?
Only under a roof. Felt soaks up water and holds grit, so on an open deck or patio choose a silicone cap. The <a href="/products/felt-lined-metal-chair-leg-caps">felt lined metal chair leg caps</a> suit a covered porch, a sunroom or chairs brought indoors.




