Felt Lined Metal Chair Leg Caps, Clear, 4 Pack
4 clear felt lined caps of one size, one chair
$12.99 · Free US shipping until Dec 31
Clear PVC caps that slip over the bottom of round or square metal tube legs, with a black felt pad underneath. The felt lets steel chairs and stools slide on hard floors instead of scraping them.
- 4 caps of one size and shape per pack, enough for one chair
- Round 16, 19, 22 or 25 mm, or square 20 x 20 mm (0.79 x 0.79 in)
- Size is the cap inside size: match it to the outside of your tube
- Clear PVC cup with a black felt pad; no glue needed
Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.
- Secure checkout: pay with PayPal, Shop Pay or card
- Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
- 30-day refund policy · Size guide
Felt lined metal chair leg caps slip over the bottom of a steel tube leg and put a black felt pad between the metal and your floor. Each cap is a clear PVC cup made for one tube size, so it hugs the leg instead of sitting loose, and the clear plastic keeps the look of the chair. There is no glue: push the cap on and the snug fit holds it.
Comparing options? Browse all metal chair leg caps and plastic chair leg caps, or read how to measure chair legs for protectors before you order.
Sizes and what is in the pack
Every pack holds 4 caps of one size and shape, enough for the four legs of one chair; order one pack per chair. The size given is the inside of the cap, which should match the outside of your tube.
| Option | Fits tube (outside) | Caps |
|---|---|---|
| Round 16 mm | 16 mm (5/8 in) | 4 |
| Round 19 mm | 19 mm (3/4 in) | 4 |
| Round 22 mm | 22 mm (7/8 in) | 4 |
| Round 25 mm | 25 mm (about 1 in) | 4 |
| Square 20 x 20 mm | 20 x 20 mm (0.79 x 0.79 in) | 4 |
How to measure your leg
Measure across the outside of the tube at the very bottom, where the cap will sit. A caliper is the most accurate tool; a ruler held across the end works too. For a square tube, measure one flat side, not the diagonal.
Choose the size that matches. A tube clearly bigger than the cap will not go in, and a tube more than about a millimeter smaller can sit loose and slip off. Tube sold in inches converts like this: 5/8 in is 16 mm, 3/4 in is 19 mm, 7/8 in is 22 mm (the usual steel folding chair tube) and 1 in is 25.4 mm, the nearest match to Round 25. A 3/4 in square tube is 19 mm, about 1 mm under Square 20, so the cap may sit a little loose on it.
How to fit them
- Turn the chair or stool over and wipe the tube ends clean.
- Take off any old worn cap or glide.
- Line the cap up with the tube, open side toward the leg, and push it on until the tube reaches the floor of the cap.
- Stand the chair up and check that every felt pad sits flat on the floor.
Where they work, and where they do not
Felt slides on hardwood, laminate, tile and vinyl, so these caps suit steel folding chairs, metal kitchen and dining chairs, tube stools and small tube table legs that get moved often. The PVC is soft enough to squeeze by hand, which helps it close around the tube. For tables with thicker legs, see all table leg caps.
They are not right for every leg:
- Bigger legs. These stop at 25 mm round and 20 mm square. For 38, 50 or 60 mm round legs and 38, 40, 50 or 60 mm square legs, see large furniture leg caps; for other square sizes see square chair leg caps.
- Angled legs. On a leg that meets the floor at a slant, the cup tilts and the felt touches on one edge only.
- Sled bases and runners. Where the tube lies along the floor, a cap on the end does not carry the weight.
- Carpet and outdoor ground. Felt helps on hard floors only and is not made for wet patios. See outdoor chair leg caps.
- Shaped or flared leg ends. If the outside of the leg is not a straight tube but the end is open, a push-in chair leg plug fits inside the tube instead.
- No felt wanted. For a cap without felt, see silicone chair leg protectors.
Felt wears down with daily dragging. Check the pads now and then, and change the caps when the felt gets thin or picks up grit. To compare these caps with plugs, covers and glides, see all replacement chair feet.
Questions
Why felt on a metal leg cap?
Rubber and silicone leg caps grip the floor. The felt pad under these caps lets a metal chair slide on hardwood, laminate, tile and vinyl instead.
How exact is the size?
Each cap is made for one tube size, and the size given is the cap inside size. Measure the outside of the tube at the bottom and choose the match; our size guide shows how.
Round or square?
Round in 16, 19, 22 and 25 mm, and square in 20 x 20 mm. Each pack is one size and shape.
How many come in a pack?
4 caps of one size, enough for one chair with four legs. For four chairs, order four packs.
Will they fit a steel folding chair?
Most steel folding chairs use 7/8 in (22 mm) tube, which matches Round 22 mm. Measure yours first, and check the tube end is straight, not flattened or angled.
Are they silicone?
No. They are clear PVC with a black felt pad underneath. The PVC is soft enough to squeeze by hand.











