No scrape. No scuff. No noise.Free US shipping until Dec 31
Chair leg plugs: one pushed into the end of a round steel tube, one loose beside it showing the ribbed fins and hollow stem
All 10 black plastic plugs in one pack, seven head up and three turned over to show the hollow ribbed stem
Black plastic plug in the end of a chrome tube chair leg standing on a grey tile floor
Hand holding a black ribbed plug at the open end of a round metal tube, ready to push it in
Close-up of two black plastic tube plugs: the smooth round head and the three flexible fins around the hollow stem

Chair Leg Plugs

10 black plastic plugs, one tube size per pack

$17.99 · Free US shipping until Dec 31

Black ribbed plastic plugs that push into the open end of a round metal chair or table leg. Pick your tube's outside diameter, from 16 mm (5/8 in) to 38 mm (1.5 in), and all 10 plugs come in that size.

  • 10 plugs per pack, all the same size
  • 8 sizes for round tube: 16 to 38 mm (5/8 to 1.5 in) outside diameter
  • Ribbed stem pushes into the tube; the round head covers the cut end
  • Black plastic, no glue or screws needed
Tube outside diameter

Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.

  • Secure checkout: pay with PayPal, Shop Pay or card
  • Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
  • 30-day refund policy · Size guide
American Express Apple Pay Diners ClubDiscoverGoogle Pay Mastercard PayPalShop Pay Visa

Chair leg plugs close the open end of a round metal tube leg with a smooth plastic head. When the original glide falls out of a steel chair or table leg, the bare cut edge of the tube rests on the floor. Push one of these black ribbed plugs into the tube and the head covers that edge again. They work as chair leg end caps that sit inside the tube instead of over it. Each pack holds 10 plugs in the size you choose.

Shopping for something that fits over the leg instead? See chair tips and metal chair leg caps, or read how to measure chair legs for protectors before you order.

Sizes and what is in the pack

Sizes are the outside diameter of the tube. The round head of the plug is the same width, so it lines up with the outside of the leg.

Size (tube outside diameter) Inches Plugs per pack
16 mm 0.63 in (5/8 in) 10
19 mm 0.75 in (3/4 in) 10
22 mm 0.87 in (7/8 in) 10
25 mm 0.98 in (about 1 in) 10
28 mm 1.10 in 10
30 mm 1.18 in 10
32 mm 1.26 in (about 1 1/4 in) 10
38 mm 1.50 in (1 1/2 in) 10

Every plug is black plastic with a flat round head and a hollow stem ringed by three flexible fins. On the 16 mm size the head is 4 mm thick and the stem goes 12.5 mm into the tube.

How to choose the right size

  1. Turn the chair over and look at the leg end. It must be a round, hollow tube with an open end.
  2. Measure straight across the outside of the tube in millimeters. A caliper is most accurate; a ruler held across the center works too.
  3. Pick the size that matches. If you measure 7/8 in, choose 22 mm; if you measure 1 in, choose 25 mm.

These plugs are made for thin-walled furniture tube. If the tube wall is very thick, the stem may not fit inside, so check that the opening is close to the outside size.

How to fit them

  1. Pull out any broken glide and wipe the tube end clean.
  2. Line the plug up with the opening, fins first.
  3. Press it in by hand, or tap the head gently with a rubber mallet, until the head sits flat on the end of the tube.

The fins bend as they go in and press against the inside wall, which holds the plug in place. No glue or screws are needed.

Where chair leg plugs work, and their limits

They suit steel and aluminum tube chairs, stools, table frames, desk legs and shelving with round open ends, on tile and concrete floors. They also close off open tube ends on frames that do not touch the floor. See every push-in option in plastic chair glides for metal legs.

The head is plastic, not felt or rubber, so it slides rather than grips, and grit caught under it can scratch. On hardwood, laminate or vinyl, felt lined metal chair leg caps are softer underfoot for legs from 16 to 25 mm. These plugs fit round tube only; for square tube, see square chair leg plugs. If the leg end is bent, squashed or closed, a cap that slips over the outside fits better: browse metal chair leg caps.

Questions

How do I measure for a plug?

Measure straight across the outside of the tube end and pick that size; the head is the same width as the tube. The tube must be round, hollow, open at the end and thin-walled, so the ribbed stem can go inside. Our size guide shows how to measure.

Do you sell square plugs?

Yes: square chair leg plugs for 1.5 in (38 mm) square tube. The plugs on this page fit round tube only.

Plug or outer cap?

A plug sits inside the tube and its head covers the cut end. An outer cap slips over the outside of the leg. Plugs suit clean, round, open tube ends; if the end is bent, squashed or closed, use metal chair leg caps that fit over the outside.

How many come in a pack?

10 plugs, all in the size you pick. That covers two four-legged chairs with two spares.

Will they fit a 7/8 inch folding chair?

Choose 22 mm (7/8 in) if the leg ends in an open round tube. If the end is flattened or already closed, folding chair feet caps that slip over the leg are the better fit.

Are they gentle on hardwood?

The plastic head is smoother than a bare steel edge, but it is plastic, not felt. For hardwood, felt lined metal chair leg caps are softer underfoot in sizes 16 to 25 mm.

More in Plastic Chair Glides for Metal Legs

See all Plastic Chair Glides for Metal Legs

Cart • 0 items

Loading your bag…