No scrape. No scuff. No noise.Free US shipping until Dec 31
Self adhesive chair sliders stuck under a chair leg
All 8 sliders in one pack: four face up showing the blue-gray face, four face down showing the paper liner
Blue-gray slider under a round wooden chair leg, seen at floor level
Hand pressing a slider onto the flat end of a square wooden chair leg, chair turned on its side, with the peeled paper liner beside it
The 40 mm and 50 mm sliders side by side, with a third slider showing its black edge and paper liner

Self Adhesive Chair Sliders

8 round sliders, 40 or 50 mm, one pack

$19.99 · Free US shipping until Dec 31

Stick-on sliders for the flat bottoms of chair and table legs. Each round slider has a smooth blue-gray resin face and an adhesive back, and one pack of 8 covers two four-legged chairs.

  • 8 round sliders per pack, all one size
  • 40 mm (1.57 in) or 50 mm (1.97 in) across
  • Smooth blue-gray resin face over a thin black layer
  • Adhesive back: peel off the paper liner and press on
SizeHow to measure

Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.

  • Secure checkout: pay with PayPal, Shop Pay or card
  • Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
  • 30-day refund policy · Size guide
American Express Apple Pay Diners ClubDiscoverGoogle Pay Mastercard PayPalShop Pay Visa

Self adhesive chair sliders stick to the bottom of a chair or table leg and put a smooth, hard face between the leg and the floor. Each round slider has a blue-gray resin face, a thin black layer under it and an adhesive back. Peel off the paper liner, press the slider on, and the leg rests on the slider instead of its own wood or metal edge.

You may also see them sold as self adhesive furniture sliders. They sit in our chair sliders range. For glides that fix to the leg in other ways, see all chair glides. Before you choose a size, read how to measure chair legs for protectors.

Sizes and what is in the pack

Size Fits leg bases In the pack
40 mm (1.57 in) across 40 to 49 mm (1.57 to 1.93 in) 8 sliders
50 mm (1.97 in) across 50 mm (1.97 in) and wider 8 sliders

Every slider is round, and each pack holds 8 sliders of one size, enough for two four-legged chairs. Sizes are not mixed in one pack. The supplier does not list a thickness or a weight limit, so we do not quote one.

How to choose and measure

Turn the chair over and measure straight across the flat bottom of one leg. Pick the slider that is the same size as the base or a little smaller. A slider that sticks out past the edge can catch when the chair moves, and that pull is what lifts the adhesive.

On a square leg, measure one side of the square; the round slider sits in the middle and leaves the corners bare. On a tapered leg, measure the very bottom, not the middle of the leg. If the base is under 40 mm (1.57 in), these sliders are too big; chair leg caps come in smaller sizes.

How to fit them

  1. Clean the bottom of the leg and let it dry. Remove old felt, glue and dust, because the adhesive only holds on a clean, flat surface.
  2. Peel the paper liner off the back without touching the adhesive.
  3. Center the slider on the leg and press it firmly for about 30 seconds.
  4. Leave the chair for a few hours before you drag it, so the adhesive can settle.

Where they work, and where they do not

They suit chairs and tables with flat wooden, metal or plastic bases that get pulled in and out. The face is hard and smooth, so the leg slides on the slider rather than scraping along on its own edge.

They are not for every leg. On an open metal tube there is nothing flat for the adhesive to hold, so use plastic chair glides for metal legs. Sled bases and legs with casters are also a poor match, and legs that meet the floor at an angle need angled chair leg floor protectors.

Chairs that are dragged hard many times a day can push any stick-on slider off over time. Slip-on chair leg caps grip the leg itself.

To move heavy furniture across a room, look at furniture sliders, which go under the load for the move and come off afterwards.

Questions

What are they made of?

The supplier lists the face as resin. Under it is a thin black layer, then an adhesive back covered by a peel-off paper liner. There is no felt and no nail.

40 or 50 mm?

Measure the flat bottom of the leg and choose a slider the same size or just smaller: 40 mm for bases of 40 to 49 mm, 50 mm for bases of 50 mm and wider. Our size guide shows how to measure.

Do they stay on?

They stick to the base of the leg with their adhesive back. They need a clean, dry, flat base, with no part of the slider hanging over the edge. For chairs dragged hard every day, chair leg caps that grip the leg stay on longer.

How many come in a pack?

8 sliders of one size, enough for two four-legged chairs.

Do they fit metal tube legs?

Only if the tube has a flat closed end. On an open tube there is nothing for the adhesive to hold, so use plastic chair glides for metal legs.

More in Chair Sliders

See all Chair Sliders

Cart • 0 items

Loading your bag…