
Folding Chair Feet Caps
Folding chair feet caps cover the bottom of each steel folding chair leg so bare metal stops scratching and clacking on your floor. Most steel folding chairs use 7/8 in (22 mm) round tube, and every cap and plug here comes in that size. The felt lined metal folding chair leg caps and the plugs also come in 3/4 in (19 mm) and 1 in (25 mm).
Pick by the leg end. Clear felt lined metal chair leg caps slip over the tube with a felt pad underneath, so the chair slides and bare metal never touches the floor. When the old foot has fallen out and the tube end is open, chair leg plugs push inside it.
Measure the outside of one leg before you order. Our guide on how to measure chair legs for protectors shows where to measure.
How to choose folding chair feet caps
Two questions settle it: is the leg end a straight round tube or an open hole, and what floor does the chair stand on?
| Type | Fits | Floor | Attaches by |
|---|---|---|---|
| Felt lined caps | Round 16 to 25 mm; square 20 mm | Hard floors. Felt slides | Slips over the tube |
| Push-in plugs | Open round tube, 16 to 38 mm | Tile, concrete. Plastic head slides | Pushes into the tube end |
Hard floors means hardwood, laminate, vinyl and tile. Each pack holds one size, and each chair needs four, one per leg.
The plugs come 10 to a pack, enough for two chairs with two spares, so a set of 20 chairs (80 legs) takes eight packs. The felt lined caps show their pack count on the product page.
How to measure a folding chair leg
- Fold the chair and lay it on its side.
- Pull off any old foot or glide so you can see the bare tube.
- Measure straight across the outside of the tube at the bottom, with calipers or a ruler.
- Match the number: about 19 mm is 3/4 in, about 22 mm is 7/8 in, about 25 mm is 1 in.
Plug sizes use the same number: the outside of the tube, not the hole. For a plug, also check that the end is open and hollow. If you own chairs from different sets, measure one from each, because a pack holds one size only.
Honest limits
- Flattened or pinched leg ends. Caps need a straight round tube to grip, and plugs need an open end. If the end is squashed flat, none of these fit.
- Round tube. The plugs fit round tube only. The felt lined caps also come in square 20 x 20 mm.
- Angled legs. Folding chair legs meet the floor at a slight angle, so a cap can wear more on one edge. Check them now and then and replace any that wear through.
- Slide, not grip. The felt lined caps and the plug heads both let the chair slide. Felt wears with daily dragging and does little on carpet.
- Plug heads are hard plastic. Grit caught under them can scratch. On hardwood, laminate or vinyl, the felt lined caps are softer.
- Plastic-frame folding chairs. Leg sizes and shapes vary, so measure before you order.
For other furniture, browse all furniture protectors. For metal chairs that do not fold, see metal chair leg caps.
Related guide: How to stop chairs from scratching floors
Folding Chair Feet Caps: questions and answers
What size are folding chair feet?
Most steel folding chairs use 7/8 in (22 mm) round tube; some use 3/4 in or 1 in. Plastic-frame chairs vary, so measure the outside of one leg. Our guide on <a href="/pages/size-guide">how to measure chair legs for protectors</a> shows how.
Felt lined cap or plug?
A felt lined cap slips over the outside of the tube and slides on hard floors. A plug pushes into an open tube end, and its plastic head slides. Choose the plug when the old foot has fallen out and the end is open and hollow.
Do padded folding chairs use the same size?
Usually yes. Padded steel folding chairs mostly use 7/8 in tube. Measure one leg to be sure.
How many caps do I need?
Four per chair, one for each leg. Each pack holds one size; a pack of plugs holds 10, and the felt lined caps show their pack count on the product page.
Can the caps go over the old plastic feet?
No. Pull the old feet off first. The caps grip the bare tube, and the plugs go into the open tube end.
Which metal folding chair leg caps are gentlest on a hardwood floor?
<a href="/products/felt-lined-metal-chair-leg-caps">Felt lined metal chair leg caps</a>: the felt slides without scraping. Plug heads are hard plastic, so they suit tile and concrete better.



