No scrape. No scuff. No noise.Free US shipping until Dec 31
Chair risers clamped on a square dining chair leg
Four brown chair risers on white, showing the corner jaws, the hex screw and the felt base
Brown chair risers under the straight square legs of a wooden dining chair on a hardwood floor
Hand turning a hex key in the corner screw of a brown riser to clamp it on a square wooden leg
Four black chair risers on white, showing the corner jaws, the hex screw and the felt base
Black chair risers clamped on white square table legs on a gray tile floor

Chair Risers for Square Legs, Clamp-On

4 clamp-on risers, 5.2 cm (2 in) lift, one pack

$35.99 · Free US shipping until Dec 31

Clamp-on chair risers that lift a chair or table 5.2 cm (about 2 in) with no glue or drilling. A screw draws two lined corner jaws onto the leg, and a felt pad sits under each riser.

  • Fits square legs 2.2 to 4.2 cm (0.87 to 1.65 in) wide
  • Adds a fixed 5.2 cm (2.05 in) of height
  • Clamps on with a hex screw, no adhesive
  • Felt base; PA6 nylon with 30% fiber body
Color

Not happy, or the wrong size? Email us within 30 days of delivery and we refund you. No need to send anything back.

  • Secure checkout: pay with PayPal, Shop Pay or card
  • Free tracked US shipping until Dec 31, 2026. Estimated delivery 6 to 14 business days after you order
  • 30-day refund policy · Size guide
American Express Apple Pay Diners ClubDiscoverGoogle Pay Mastercard PayPalShop Pay Visa

Chair risers lift a chair or table by 5.2 cm (about 2 in) without glue, screws into the wood or drilling. Each riser clamps around the bottom of a square leg from 2.2 to 4.2 cm wide, and a felt pad under the base sits on the floor. One pack of 4 does one chair or one small table.

Need a different fit? Browse all chair leg extenders, see our stick-on furniture leg extenders for round or wider legs, or read how to measure chair legs for protectors before you order.

Sizes and what is in the pack

Measurement Metric Inches
Fits square legs 2.2 to 4.2 cm 0.87 to 1.65 in
Height added 5.2 cm 2.05 in
Overall height with jaws 8.3 cm 3.27 in
Base 5.5 x 5.5 cm 2.17 x 2.17 in
Clamp jaw height 3 cm 1.18 in
Risers per pack 4, one color

The body is PA6 nylon with 30% fiber. Black lining pads cover the inside of both jaws, and dark brown felt covers the base. Choose black or brown plastic to match the furniture.

How to measure your legs

Measure straight across one flat side of the leg, 2 to 3 cm up from the floor, since that is where the jaws grip. If the leg is between 2.2 and 4.2 cm (0.87 and 1.65 in) wide and stands straight down, these risers fit. A leg that tapers slightly still fits if its bottom 3 cm is inside that range.

How to fit them

  1. Tip the chair over onto a soft surface so the legs point up, or lift one leg at a time.
  2. Turn the screw on the corner of the riser counterclockwise with a hex (Allen) key to open the jaws wider than the leg. The supplier pack list names only the risers, so have a key ready.
  3. Push the riser onto the leg until the leg end sits on the platform inside.
  4. Turn the screw clockwise until both lined jaws press firmly on the leg corners. Stop when it is snug; the body is plastic.
  5. Fit all 4, stand the chair up and check that it does not rock. Tighten again after a week of use.

Where they work, and their limits

Use them to raise a dining chair for a taller person, bring a desk or table to a better working height, or give a low cabinet more floor clearance. The felt base suits hardwood, laminate, vinyl and tile.

They are made for legs that stand straight down. Chairs with splayed or angled legs will not sit flat in them, and the supplier marks those as not suitable.

The supplier also shows them on a round leg, but the square jaws touch a round leg at only two points. For round legs, or square legs wider than 4.2 cm (1.65 in), our furniture leg extenders stick under a flat foot instead of clamping. For furniture that stays put, self adhesive furniture risers add a fixed 2 in (50 mm) under a round or square foot up to 40 mm (1.57 in) across.

The height is fixed at 5.2 cm (about 2 in), and the supplier does not state a maximum load. Before regular use, sit at the table and check that your knees still clear the table edge.

Questions

What legs do they fit?

Square legs from 2.2 to 4.2 cm (0.87 to 1.65 in) wide that stand straight down. Measure across one flat side, 2 to 3 cm above the floor.

How much height do they add?

5.2 cm (about 2 in). The height is fixed; only the clamp width adjusts.

How do they attach?

They clamp around the leg. A screw through the riser pulls two lined corner jaws onto opposite corners of the leg, with no adhesive and no drilling.

Do I need a tool?

Yes, a hex (Allen) key to turn the screw. The supplier pack list names only the risers, so have one ready.

How many come in a pack?

4 risers in one color, enough for one chair or one small table.

Will they fit round or splayed legs?

Splayed or angled legs will not sit flat in them, and the supplier marks those as not suitable. The square jaws hold a round leg at only two points. For round legs with a flat foot, see our furniture leg extenders, which stick under the leg.

More in Chair Leg Extenders

See all Chair Leg Extenders

Cart • 0 items

Loading your bag…